Results 1 to 12 of 12

Thread: Side Pipe Temps

  1. #1
    Join Date
    Sep 2003
    Location
    Roseville, CA, USA.
    Posts
    2,323

    Side Pipe Temps

    Have any of you measured the temp of your side pipes using one of those infared/laser hand held gadgets?
    Phil

    427 Roadster, #4279436
    FE Specialties FE
    3:31 and Toploader (wide ratio)

    Roseville (N.Cal)

  2. #2
    Join Date
    Jan 2003
    Location
    Rocky River, ohio, USA.
    Posts
    388
    I've used my legs on two seperate occasions and I gotta tell you that "they're farkin' hot"
    AL
    2899386

  3. #3
    Join Date
    Sep 2003
    Location
    Roseville, CA, USA.
    Posts
    2,323
    Thanks, Al.... I know they are hot 'cause I just toasted mine for the second time in as many years. I'm curious as too "how hot" they get, because it only takes a nano-second to cause some serious damage
    Phil

    427 Roadster, #4279436
    FE Specialties FE
    3:31 and Toploader (wide ratio)

    Roseville (N.Cal)

  4. #4
    Join Date
    Jan 2003
    Location
    Rocky River, ohio, USA.
    Posts
    388
    I've got a temp gun and the next time I fire it up I'll shoot it and see where the temps are....
    AL
    2899386

  5. #5
    Join Date
    Jan 2003
    Location
    Shepherdsville, KY, USA.
    Posts
    1,725

    Thumbs up Yep!

    I have shot everthing on the Cobra with my infared temp. gun.

    Around the collector area, 4 bolts, end of the header, 375 to 425 degrees.

    Rear brake rotors under heavy braking around 400 degrees, while the vented front rotors run 250-260. Thats why you have to change the differental grease more often. The rear rotors help heat it up since the are attached to the stub axles right out of the differental.

    Tire temperatures usually run 105 to 117, a car that is aligned good with the correct tire pressure, the variation wil be within 2-3 degreees.

    Great little device, you can shoot the rear hub bearings, wheel bearings, all sorts of things. Even tell you when the beer is ready to consume, 34 degrees.
    Rick
    427 S/C , 427 Side-oiler, 4 Speed Close Ratio Top Loader, 3:73 Gear
    #4279405

  6. #6
    Join Date
    Sep 2004
    Location
    ranburne, alabama, USA.
    Posts
    620

    We

    all have the cobra tattoo---or some call it a tramp stamp neatly fried into a leg somewhere, they get hottt.Will-alabama

  7. #7
    Join Date
    Sep 2003
    Location
    Roseville, CA, USA.
    Posts
    2,323
    Rick - thanks for the info, although they seem a lot hotter

    Will - I prefer "badge of honor", to tramp stamp. Out here, one of those tattoo's in the small of one's back is referred to as a tramp stamp
    Phil

    427 Roadster, #4279436
    FE Specialties FE
    3:31 and Toploader (wide ratio)

    Roseville (N.Cal)

  8. #8
    Join Date
    Jan 2003
    Location
    Shepherdsville, KY, USA.
    Posts
    1,725

    Ceramic Coating, Silver

    I am sure the black pipes are hotter, one problem with infared the silver coating will effect the reading, reflective material. Also has to do with the type fuel and how hard you run the engine. So I am sure that over 500 degrees is possible.
    Rick
    427 S/C , 427 Side-oiler, 4 Speed Close Ratio Top Loader, 3:73 Gear
    #4279405

  9. #9
    Join Date
    Feb 2005
    Location
    savannah, ga, USA.
    Posts
    225
    Rick,
    I would have guessed front rotors to get hotter because they carry more of the load. When adjusting my brake bias, I assummed that. Maybe I should look at them again. Thanks for the info.
    Walter

  10. #10
    Join Date
    Aug 2005
    Location
    easley, south carolina, USA.
    Posts
    70

    Unhappy side pipe burn

    I like to refer to it as a snake bite . I am trying to get over my first bite now . Hope to never get bitten again . It does hurt . It is just like a snake .You never see it comming but you sure know you have been bitten .

    Happened about two weeks ago still feels like it just happened .
    Rick Findley

  11. #11
    Join Date
    Jan 2003
    Location
    Shepherdsville, KY, USA.
    Posts
    1,725
    Walter,

    You have to remember, the rear inboard rotors carry more tempertature because:

    They are solid rotors
    They do not get the air circulation the fronts get
    They are ajacent to a rear end that is running at 125-150 degrees.

    The fronts have directional vanes, and are not solid, they get good air flow.
    Rick
    427 S/C , 427 Side-oiler, 4 Speed Close Ratio Top Loader, 3:73 Gear
    #4279405

  12. #12
    Join Date
    Dec 2004
    Location
    Prince Frederick, Maryland, USA.
    Posts
    1,561
    I have measured 510*F at the 4 tubes at an Idle from a cold start to warm up. I have black sidepipes.
    Wear long jeans when driving your Cobra.

    140*F will scald you in 5 seconds. There is no escape at 500*F.
    Tony
    Unique 427 #4279480 Precision Engine Machine Company 427 s/o 483.47 stroker close ratio toploader 3.31 jag rear

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •