Are there things that work themselves loose? What do you typically "tighten up" on a periodic basis? thanks peter
Are there things that work themselves loose? What do you typically "tighten up" on a periodic basis? thanks peter
I would periodically check the loose nut between the steering wheel and the driver's seat
Sorry for not sending a serious reply.......couldn't help it.
With a new build, you should tighten the exhaust manifold, oil pan and valve cover bolts.
Steering linkages and suspension bolts as well.
In a word.... EVERYTHING!
The engine and drive train components are obvious, however, doors may fall off if the shoulder bolts loosen up, you might have a wind wing or sun visor disappear one afternoon, that rattling you hear could be your trunk lid due to the hanger for the hinges not being tight. At least that's what I've heard from others
Phil
427 Roadster, #4279436
FE Specialties FE
3:31 and Toploader (wide ratio)
Roseville (N.Cal)
Peter
I've owned British sports cars since 1969 and have developed the habit of occasionally checking every reachable fastening for tightness and security. I know the Weavers found several steering joints that required setscrew tightening while spot-checking 2002 Homecoming participant cars.
- Geary
I routinely have to tighten up the door latches ..... and the set screws on my steering linkage have loosened up as well.
Bob
I'm amazed at how many cars I check have a loose steering wheel, if you feel looseness in the wheel just tighten the nut.
Alan
Yes that is amazing, I got in to Unique's 289 car in Pigeon Forge 2 years ago and the steering wheel nearly fell off in my hand....couldnt help it Alan!!!!
Rick
427 S/C , 427 Side-oiler, 4 Speed Close Ratio Top Loader, 3:73 Gear
#4279405
Good rule of thumb...for each spring when you change the spark plugs, change the oil, change the brake fluid(yes replace the brake fluid on an annual basis or after serious track driving/ per Valvoline Engineer) and you take the wheels off and repack the front bearings, and put a grease gun on all the fittings. Then you wipe off all that stuff you accumulated for the previous year from underneath the car....
Rule # 1...If you can put a wrench(Allen, torx, metric, standard) you tighten it.
Rule # 2....Torque the lug luts when you put the wheels back on.
I cannot tell you how many nuts and bolts I have picked up walking the track before and after an event.....richard
dickieboy7
Unique 289FIA-Green
351C-4V cobra jet
Toploader
did it myself..and fix it
Make SURE you check the drive shaft fasteners periodically. That one is pretty ugly when it creeps up on you.
427SC, Torch Red / white stripes
427 Windsor Stroker from Southern Automotive
Delicious example of Beauty + Power.
Drive shaft to rear end. I checked mine after 5000 miles and two of the nuts were finger loose. Exhaust manifold is probably what comes loose the most.
Bob
I think a regular routine to go over the car is very important. I also use green Loctite for a little insurance.
Ralph
The bolts on my driveshaft were loose too. Is there any disadvantage using loctight on these critical items?
Not from my perspective.
Phil
427 Roadster, #4279436
FE Specialties FE
3:31 and Toploader (wide ratio)
Roseville (N.Cal)
Yes, unless you want a permanent bond, DONT use the Red!!
Rick
427 S/C , 427 Side-oiler, 4 Speed Close Ratio Top Loader, 3:73 Gear
#4279405
Use an anti-seize and snug them up just like you would any other vehicle.
Phil
427 Roadster, #4279436
FE Specialties FE
3:31 and Toploader (wide ratio)
Roseville (N.Cal)
Dave
93 Unique Motorcars 427 SC, 428PI with CJ heads, toploader 4 spd,jag rear with 354 gears, Red with white stripes.
just a precaution
Phil
427 Roadster, #4279436
FE Specialties FE
3:31 and Toploader (wide ratio)
Roseville (N.Cal)
Thanks, Next time for sure, still interested in the proper toreque though!
Dave
93 Unique Motorcars 427 SC, 428PI with CJ heads, toploader 4 spd,jag rear with 354 gears, Red with white stripes.
90-100 Ft Lbs
Rick
427 S/C , 427 Side-oiler, 4 Speed Close Ratio Top Loader, 3:73 Gear
#4279405