Tilton Flywheel-Clutch-Hyd. Release Bearing

[V8er]

I'd appreciate input from anyone who's had experience with Tilton Clutch-Flywheel assemblies, preferably the complete Tilton Flywheel-Clutch-Hydraulic Throwout package. But any input or tips on a particular aspect would be beneficial.

My FIA will be used primarily for spirited two-lane touring (read occasional non-competitive road racing), NOT long Interstate spans or drag racing.

I am mating a SBF with an estimated 460hp/450lb.-ft. to a Toploader. I would like to use a recommended Tilton OT-Series 7.25”, 2-plate Rally Clutch, Cerametallic disks, 157T Flywheel, Hydraulic Release Bearing.

1. Since the SBF has a 28oz. imbalance and the Tilton Flywheel is neutral balance, should I:

a. Add the 28oz. imbalance weight to the Tilton “neutral” balance Flywheel?

i. Weld the weight or tap and bolt in on?

b. Drill the opposite side to compensate?

c. Internally balance the engine using a “neutral” balance Tilton Flywheel and “neutral” balance Harmonic Balancer?

2. Is there any benefit or detriment to:

a. The Sintered Metallic versus the Cerametallic disks?

b. Are they equally safe from blowup?

3. Is there any benefit or detriment to:

a. The more expensive 600-series Hydraulic Release Bearing which is a simpler "bolt-on" the transmission item?

b. The less expensive 400-series requiring machining/modification to bellhousing/fitting to attach to the inside of the bellhousing?

4. Since a Tilton OT-Series clutch does not slip until the torque is 50% above the rated torque capacity, (making the rating rather conservative) should I:

a. Adhere to the pressure plate ratings or add margin capacity?

b. Consider the “High” or “Ultra-High” Pressure Plate Ratio?

5. Is this assembly:

a. As safe (“blow-proof”) as advertised?

b. Safe enough that I could use an original FoMoCo aluminum bellhousing?

[Aggressor]

In response to some of your questions:

I would have the entire rotating assembly (Including flywheel) precision balanced together by a good machinist. If you are off by only a a little bit when adding or removing balance weight, it can yield pounds of off balance rotating mass.

Your don't really have to go nuts on saving a few pounds. The car weighs in at say 2500 lbs. It gets to be a bit achedemic if your net power to weight ratio is 4.5 pounds per horsepower or 4.9. Either way it can be a wild crazy ride down the street. My car is quite a bit on the extreme side which is cool for bragging rights but looking back it was much more pleasant/fun to drive before the upgrades.

I would not want an aluminum bellhousing and fiberglass to be the only protection between me and the flywheel/clutch assembly. I used a Lakewood scattershield on my build as you never know when the spirited driving becomes high rpm stratospheric shifts to prove a point or just to pin your butt back into the seat for the thrill of it.
As Tom McCahill once said: "It's like being hit in the small of your back by a Louisville Slugger in the hands of Mickey Mantle"

- Geary

[TurnpikeBoy]

OK, let's try. (1) The flywheel must have the 28 oz. weight attached - usually the mfgr provides both 28 and 50 oz wts, and they screw onto the flywheel with included screws (2) Don't use a dual-disc clutche so really can't comment other than why the dual? - a single 10.5" will hold your setup with far more simplicity (3) simpler is better (4) what is the clutch rated for? - gotta believe it's way past what you're intending to put thru it (5) scattershields are good insurance no matter what the clutch mfgr says. Drag racing is the hardest app for a clutch, and since you say you're not going drag racing you could probably use the Ford housing. Just be aware it will offer you utterly no protection if something came apart in the clutch.

But I still have to ask - why a dual-disc? Just one opinion here....They're more complication than a typical single-disc by far, have had noise/grabbiness/harshness issues for a long time, and won't offer you any discernable advantage for your stated use.

[V8er]

Aggressor,
I have the complete engine in a competent machine shop (Vilas Motor Works, Bryan, TX) and intend to balance the entire assembly, my question is: Should I leave it external balance by using a 20oz. harmonic balancer and modifying the flywheel to effectively be 20oz. or try to internally balance it with "neutral" balance flywheel and harmonic balancer?

TurnpikeBoy,
Please note that I'm considering a Tilton OT-II Series 7.25”, 2-plate Rally Clutch, Cerametallic disks, 157T Flywheel, Hydraulic Release Bearing.

This 7.25”, 2-plate racing-style clutch is what is recommended for the nearly 500 lb./ft. capacity, extra torque. Since this is not an "OE" size (10.5" or 11") clutch, the usual/traditional rules don't apply. It's a simple but rugged, compact, lightweight system.

The Tilton 9 lb. Flywheel apparently is only available in a "neutral" balance so I'll either have to add the weight or internally balance the 351C. This is my dilema.

From the Cobra Automotive catalog:
Tilton Racing Clutches
"These small multi-disc clutch setups greatly reduce rotating weight and offer instant lock up with metallic lined solid clutch discs. Easy to maintain and almost indestructible, these Tilton button flywheel style clutches mount to a conventional automatic flywheel and allow you to use your stock bell housing and starter. A mechanical throw out bearing utilizing standard clutch linkage can be used with this Tilton clutch. Or, if you prefer, a more driver-friendly hydraulic throw out bearing can be used as well. The benefits of this clutch assembly are countless. No need for a heavy scatter shield, much quicker throttle response and increased braking capability because of reduced momentum when the throttle is lifted. The end result is more reliability while it feels like you have 50 more HP and bigger brakes! Clutch discs are easy to replace and these setups can be rebuilt at a fraction of the cost of a new one."

From the Tilton Site:

#66-302HORA or #66-302UORA
http://www.tiltonracing.com/content....t2&id=380&m=d#

600-Series Hydraulic Release Bearing
http://www.tiltonracing.com/content.php?page=hydraulic2

[V8er]

I meant to say "28oz. imbalance flywheel and harmonic balancer".

[mkassab]

V8er, I'm posting for Brent@b2motorsportsllc.com

From Brent: (copy and paste below... he's waiting for his membership to post direct)

That particular clutch package is basically overkill (in application and
price) for what your needs are.

A simple 10.5" diaphragm pressure plate kit would work just fine and they are readily available to handle 450, 550, or 650 hp. I can provide a RAM or McLeod clutch kit that will not need to have any type of exotic friction materials to hold 450-460hp. For just street driving on street tires, an aftermarket diaphragm pressure plate with an organic/organic disc will work perfectly. Keep in mind that the more exotic disc material that's used, the more chance of chatter and poor street manners. With just 450hp, there's no need in taking that kind of chance.

I would also advise against the use of a hydraulic throw out bearing. A conventional throw out bearing and clutch fork is much more reliable, unless you absolutely have no room for a fork. Keep in mind that if anything goes wrong at all with the hydraulic bearing (and at some point, it will), then it will require removal of the transmission and associated hardware.

To answer more of your questions:

1. If your budget allows, you can internally balance. What usually has to happen is that the crankshaft will need heavy metal to balance it.
This requires drilling a hole in the counterweight, then installing a slug of heavy metal and welding it in. Heavy metal (mallory) is very expensive. If you need a lot of metal, it can raise the balancing cost significantly. For a mild street application, there's nothing at all wrong with a 28oz or 50oz imbalance.

2. Yes...As stated above, there are many different flavors of clutch disc material. Organic is the most simplest and is usually what is found in most stock applications. Kevlar, sintered bronze, sintered aluminum, sintered iron, etc, etc, are "stickier" friction materials, made to hold larger amounts of horsepower. However, the risk of bad street manners increases with these materials.

4. Again, see above. There's really no need in such an elaborate clutch setup for a street car.

5. Any performance application deserves a blow proof bellhousing, and there are no flywheel/clutch combos that will guarantee that you will not have an explosion. With only a thin layer of fiberglass between the flywheel and your legs after an explosion, I would not trust my legs to an aluminum or cast iron bellhousing.

"an instant lock-up" is not something you want with a street car, as it's either on/off, with no slippage available. It would make it pretty miserable on the street.

[pgermond]

I'm probably going to get "Flamed" for saying this by some members, but I agree.... my experience (from watching friends with HTOB) has been that a conventional throw-out bearing and clutch fork are far less maintenance and problem free than a HTOB. IMHO, any time you have hydraulic fluid that close to a clutch plate you are asking for trouble.